Our store is collecting only the most reliable options available in Malta.
Here you will find NEW RHIBS and SECOND HAND ones, NEW and SECOND HAND ENGINES and 3 different types of glues.
D-STORE is the market reference for rhibs and relative products.
Our rhibs are covered by at least one year warranty on second hand, up to 5 ys warranty on new ones.
The glues proposed have been studied and tested through years of experience and studied to provide the highest reliability both in phase of gluing and dry traction in Maltese environment!
Welcome to D-STORE.
Exellent rhib made in Italy on 2018.
Both rhib and engine are still under warranty.
The rhib comes with a Simrad go7 with all the engine reading through NMEA200. No analogic gauges are present on the dashboard.
Carbon fiber dashboard.
Radio Bluetooth
50L Shower
Navigation lights
2 batteries
Canope
Rear table
4kg anchor
Very well kept 20ft dinghy
Tubes brand new with 5 ys warranty Hypalon© 828.
GARMIN GPS
VHF Cobra
Radio
STRONG TRAILER INCLUDED
Engine and hydraulic serviced on 2021
Registered, ta’ Malta
Brand new 16ft hypalon 866 (thicker version) tubes with 5ys warranty
Brand new upholstery (march 2021)
90hp yamaha engine serviced
2x 25L fuel tanks
40L in-built water tank
Lowrance Elite-4 fishfinder with maps
Sound system Bluetooth Brand
New steering wheel
Complete new electric system
Engine in perfect running conditions.
Original working gauges.
Original throttle with blue cables for a 16ft rhib.
Mavimare & Mancini hydraulic steering year 2021.
19 pitch stainless steel prop
19 pitch aluminum prop
PARTS CHANGED ON 2021:
4 YEARS WARRANTY ON THE VESSEL BY BIG D®
P/E with other boats considered
90 HP Tohatsu Engine serviced last year
VHF
Anchor
New Fuel Tank 100 lts
New Bilge Pump
TRAILER INCLUDED
Now with S number.
The Big D® hardner is a part of the 2-component contact adhesive with a polychloroprenic gum and resin solution base, featuring a medium open time and high heat resistance.
Activator / accelerator / catalyst in bottle of 60 ml.
Purple color.
This product is what is needed to start gluing reaction with all Big D® glues.
Used from 5% to 10%, is provided a pasting cross-linking, with increase of the endurance and greater resistance to the action of reactivation generated by exposure to heat sources.
Ventilate the area during and after use.
DOCUMENTS
Two-component adhesive, available in tins of 0,5 kg or 1 kg.
Colour: opalescent, yellow.
It can be used with the activator from 5% to 10%. On high and dry environmental temperatures we suggest to keep the lowest %.
For watertight applications, it is suggested the application of two coats of glue.
Ventilate the area during and after use.
Surfaces must be polished before applying the glue and, if necessary, cleaned with a solvent to completely eliminate any and all plasticisers.
Mix half of the Big D® hardner bottle into the can and stir for 1 minute with a stick.
Apply with a short-haired brush an even and thin layer to both glue surfaces, leaving the solvent to fully dry. This process may take from 30 to 45 minutes, based on the environmental temperature.
Apply the adhesive / cross-linking mixture again and after about 20 minutes, warm up the surfaces with an hairdryer and pair the parts together while pressing down evenly.
To improve the end result and prevent air bubbles, use a roller before pressing. The dried product is odourless, flexible and resistant to ageing.
The vessel is ready for the water in 48 hours.
Click here: Big D® glue hardner
Two-component adhesive, available in tins of 0,5 kg or 1 kg.
Colour: opalescent, yellow.
It can be used with the activator from 5% to 10%. On high and dry environmental temperatures we suggest to keep the lowest %.
For watertight applications, it is suggested the application of two coats of glue.
Ventilate the area during and after use.
Surfaces must be polished before applying the glue and, if necessary, cleaned with a solvent to completely eliminate any and all plasticisers.
Mix a full Big D® hardner bottle into the can and stir for 1 minute with a stick.
Apply with a short-haired brush an even and thin layer to both glue surfaces, leaving the solvent to fully dry. This process may take from 30 to 45 minutes, based on the environmental temperature.
Apply the adhesive / cross-linking mixture again and after about 20 minutes, warm up the surfaces with an hairdryer and pair the parts together while pressing down evenly.
To improve the end result and prevent air bubbles, use a roller before pressing. The dried product is odourless, flexible and resistant to ageing.
The vessel is ready for the water in 48 hours.
Click here: Big D® glue hardner
Brand new 16ft hypalon 866 (thicker version) tubes with 5ys warranty
Hull from Magnus 16 never been even given antifouling.
Good as first rhib or as rental investment.
It can host up to 65 hp engine.
P/E with other boats considered
Two-component adhesive, available in tins of 0,5 kg or 1 kg.
Colour: opalescent.
It can be used with the activator from 5% to 10%. On high and dry environmental temperatures we suggest to keep the lowest %.
For watertight applications, it is suggested the application of two coats of glue.
Ventilate the area during and after use.
Surfaces must be polished before applying the glue and, if necessary, cleaned with a solvent to completely eliminate any and all plasticisers.
Mix half of the Big D® hardner into the can and stir for 1 minute with a stick.
Apply with a short-haired brush an even and thick layer to both glue surfaces, leaving the solvent to fully dry. This process may take from 15 to 25 minutes, based on the environmental temperature.
After about 2 hours, apply the adhesive / cross-linking mixture again. After about 20 minutes, warm up the surfaces with an hairdryer and pair the parts together while pressing down evenly.
To improve the end result and prevent air bubbles, use a roller before pressing. The dried product is odourless, flexible and resistant to ageing.
The vessel is ready for the water in 48 hours.
Click here: Big D® glue hardner
Two-component adhesive, available in tins of 0,5 kg or 1 kg.
Colour: opalescent.
It can be used with the activator from 5% to 10%. On high and dry environmental temperatures we suggest to keep the lowest %.
For watertight applications, it is suggested the application of two coats of glue.
Ventilate the area during and after use.
Surfaces must be polished before applying the glue and, if necessary, cleaned with a solvent to completely eliminate any and all plasticisers.
Mix half of the Big D® hardner bottle into the can and stir for 1 minute with a stick.
Apply with a short-haired brush an even and thick layer to both glue surfaces, leaving the solvent to fully dry. This process may take from 15 to 25 minutes, based on the environmental temperature.
After about 2 hours, apply the adhesive / cross-linking mixture again. After about 20 minutes, warm up the surfaces with an hairdryer and pair the parts together while pressing down evenly.
To improve the end result and prevent air bubbles, use a roller before pressing. The dried product is odourless, flexible and resistant to ageing.
The vessel is ready for the water in 48 hours.
Click here: Big D® glue hardner
Two-component adhesive, available in tins of 0,5 kg or 1 kg.
Colour: black.
It can be used with the activator from 5% to 10%. On high and dry environmental temperatures we suggest to keep the lowest %.
For watertight applications, it is suggested the application of two coats of glue.
Ventilate the area during and after use.
Surfaces must be polished before applying the glue and, if necessary, cleaned with a solvent to completely eliminate any and all plasticisers.
Mix half of the Big D® hardner bottle into the can and stir for 1 minute with a stick.
Apply with a short-haired brush an even and thin layer to both glue surfaces, leaving the solvent to fully dry. This process may take from 30 to 45 minutes, based on the environmental temperature.
Apply the adhesive / cross-linking mixture again and after about 20 minutes, warm up the surfaces with an hairdryer and pair the parts together while pressing down evenly.
To improve the end result and prevent air bubbles, use a roller before pressing. The dried product is odourless, flexible and resistant to ageing.
The vessel is ready for the water in 48 hours.
Click here: Big D® glue hardner
Two-component adhesive, available in tins of 0,5 kg or 1 kg.
Colour: black.
It can be used with the activator from 5% to 10%. On high and dry environmental temperatures we suggest to keep the lowest %.
For watertight applications, it is suggested the application of two coats of glue.
Ventilate the area during and after use.
Surfaces must be polished before applying the glue and, if necessary, cleaned with a solvent to completely eliminate any and all plasticisers.
Mix a full bottle of the Big D® hardner into the can and stir for 1 minute with a stick.
Apply with a short-haired brush an even and thin layer to both glue surfaces, leaving the solvent to fully dry. This process may take from 30 to 45 minutes, based on the environmental temperature.
Apply the adhesive / cross-linking mixture again and after about 20 minutes, warm up the surfaces with an hairdryer and pair the parts together while pressing down evenly.
To improve the end result and prevent air bubbles, use a roller before pressing. The dried product is odourless, flexible and resistant to ageing.
The vessel is ready for the water in 48 hours.
Click here: Big D® glue hardner
Engine in perfect running conditions.
Original working gauges.
Original throttle with blue cables for a 16ft rhib.
Mavimare & Mancini hydraulic steering year 2021.
19 pitch stainless steel prop
19 pitch aluminum prop
PARTS CHANGED ON 2021: