The innovation and research is the keyword for this company.

During these years on the island we learned that glues are reacting in different way to humidity, super-strong direct sun, environmental exposures in general.

It is normal to see that we cannot use the same glue is used in other countries because of this reason, in fact we developed a glue with certain additives which allows the professional to work in the best way and the final use to put his mind at rest.

product photo

PVC glue – 0,5 Kg

20.00

Two-component adhesive, available in tins of 0,5 kg or 1 kg.

Colour: opalescent.

Suitable for glueing any PVC based compound.

 

  • PVC rubber layers
  • handles / helms
  • watertight zippers with polyurethane tape (TiZip) or neoprene (BDM / Dynat / Otto)
  • latex terminals
  • valves
  • pockets / reinforcement patch

It can be used with the activator from 5% to 10%. On high and dry environmental temperatures we suggest to keep the lowest %.
For watertight applications, it is suggested the application of two coats of glue.
Ventilate the area during and after use.

How to Use

Surfaces must be polished before applying the glue and, if necessary, cleaned with a solvent to completely eliminate any and all plasticisers.

Mix half of the Big D® hardner into the can and stir for 1 minute with a stick.

Apply with a short-haired brush an even and thick layer to both glue surfaces, leaving the solvent to fully dry. This process may take from 15 to 25 minutes, based on the environmental temperature.

After about 2 hours, apply the adhesive / cross-linking mixture again. After about 20 minutes, warm up the surfaces with an hairdryer and pair the parts together while pressing down evenly.

To improve the end result and prevent air bubbles, use a roller before pressing. The dried product is odourless, flexible and resistant to ageing.

The vessel is ready for the water in 48 hours.

 

IMPORTANT: for using this glue you need to purchase the hardner too

Click here: Big D® glue hardner

 

Documents

Technical Data Sheet

Safety Data Sheet

product photo

PVC glue – 1 kg

32.00

Two-component adhesive, available in tins of 0,5 kg or 1 kg.

Colour: opalescent.

Suitable for glueing any PVC based compound.

 

  • PVC rubber layers
  • handles / helms
  • watertight zippers with polyurethane tape (TiZip) or neoprene (BDM / Dynat / Otto)
  • latex terminals
  • valves
  • pockets / reinforcement patch

It can be used with the activator from 5% to 10%. On high and dry environmental temperatures we suggest to keep the lowest %.
For watertight applications, it is suggested the application of two coats of glue.
Ventilate the area during and after use.

How to Use

Surfaces must be polished before applying the glue and, if necessary, cleaned with a solvent to completely eliminate any and all plasticisers.

Mix half of the Big D® hardner bottle into the can and stir for 1 minute with a stick.

Apply with a short-haired brush an even and thick layer to both glue surfaces, leaving the solvent to fully dry. This process may take from 15 to 25 minutes, based on the environmental temperature.

After about 2 hours, apply the adhesive / cross-linking mixture again. After about 20 minutes, warm up the surfaces with an hairdryer and pair the parts together while pressing down evenly.

To improve the end result and prevent air bubbles, use a roller before pressing. The dried product is odourless, flexible and resistant to ageing.

The vessel is ready for the water in 48 hours.

 

IMPORTANT: for using this glue you need to purchase the hardner too

Click here: Big D® glue hardner

 

Documents

Technical Data Sheet

Safety Data Sheet

product photo

Glue hardner – 60 ml

13.00

The Big D® hardner is a part of the 2-component contact adhesive with a polychloroprenic gum and resin solution base, featuring a medium open time and high heat resistance.

Activator / accelerator / catalyst in bottle of 60 ml.

Purple color.

This product is what is needed to start gluing reaction with all Big D® glues.

Used from 5% to 10%, is provided a pasting cross-linking, with increase of the endurance and greater resistance to the action of reactivation generated by exposure to heat sources.

Ventilate the area during and after use.

DOCUMENTS

Technical sheet

Safety sheet

This glue is providing the best bonding agent for PVC application. It has been tested that grants the traction up to 100°C.

The color is clear and tends to become yellowish if kept at straight sunlight after few days.

Lines of glue mistakes have be removed immediately after being given by using a cloth with acetone.

Perfect solution for regluing parts on any PVC device: tenders, dinghies, plc accessories, SUP, swimming pools.

product photo

Hypalon© glue – 0,5 kg

25.00

Two-component adhesive, available in tins of 0,5 kg or 1 kg.

Colour: opalescent, yellow.

Suitable for glueing any Hypalon© and Neoprene based compound.

 

  • neoprene rubber layers
  • rubber handles / helms
  • latex terminals
  • valves
  • pockets / reinforcement patch

It can be used with the activator from 5% to 10%. On high and dry environmental temperatures we suggest to keep the lowest %.
For watertight applications, it is suggested the application of two coats of glue.
Ventilate the area during and after use.

How to Use

Surfaces must be polished before applying the glue and, if necessary, cleaned with a solvent to completely eliminate any and all plasticisers.

Mix half of the Big D® hardner bottle into the can and stir for 1 minute with a stick.

Apply with a short-haired brush an even and thin layer to both glue surfaces, leaving the solvent to fully dry. This process may take from 30 to 45 minutes, based on the environmental temperature.

Apply the adhesive / cross-linking mixture again and after about 20 minutes, warm up the surfaces with an hairdryer and pair the parts together while pressing down evenly.

To improve the end result and prevent air bubbles, use a roller before pressing. The dried product is odourless, flexible and resistant to ageing.

The vessel is ready for the water in 48 hours.

 

IMPORTANT: for using this glue you need to purchase the hardner too

Click here: Big D® glue hardner

 

Documents

Technical and Safety Data sheet – 07/01/2022

product photo

Hypalon© glue – 1 Kg

37.00

Two-component adhesive, available in tins of 0,5 kg or 1 kg.

Colour: opalescent, yellow.

Suitable for glueing any Hypalon© and Neoprene based compound.

 

  • neoprene rubber layers
  • rubber handles / helms
  • latex terminals
  • valves
  • pockets / reinforcement patch

It can be used with the activator from 5% to 10%. On high and dry environmental temperatures we suggest to keep the lowest %.
For watertight applications, it is suggested the application of two coats of glue.
Ventilate the area during and after use.

How to Use

Surfaces must be polished before applying the glue and, if necessary, cleaned with a solvent to completely eliminate any and all plasticisers.

Mix a full Big D® hardner bottle into the can and stir for 1 minute with a stick.

Apply with a short-haired brush an even and thin layer to both glue surfaces, leaving the solvent to fully dry. This process may take from 30 to 45 minutes, based on the environmental temperature.

Apply the adhesive / cross-linking mixture again and after about 20 minutes, warm up the surfaces with an hairdryer and pair the parts together while pressing down evenly.

To improve the end result and prevent air bubbles, use a roller before pressing. The dried product is odourless, flexible and resistant to ageing.

The vessel is ready for the water in 48 hours.

 

IMPORTANT: for using this glue you need to purchase the hardner too

Click here: Big D® glue hardner

 

Documents

Technical and Safety Data sheet – 07/01/2022

product photo

Glue hardner – 60 ml

13.00

The Big D® hardner is a part of the 2-component contact adhesive with a polychloroprenic gum and resin solution base, featuring a medium open time and high heat resistance.

Activator / accelerator / catalyst in bottle of 60 ml.

Purple color.

This product is what is needed to start gluing reaction with all Big D® glues.

Used from 5% to 10%, is provided a pasting cross-linking, with increase of the endurance and greater resistance to the action of reactivation generated by exposure to heat sources.

Ventilate the area during and after use.

DOCUMENTS

Technical sheet

Safety sheet

Hypalon© glue is the result of a research which interested the production sector. It grants perfect bonding between neoprene surfaces and 100% reliable up to 400°C direct exposure. It can be removed if treated almost immediately (max 20 mins) after being given by using a cloth with acetone.

Works on Hypalon© rhibs, neoprene based handles and accessories, rubber supports.

product photo

X-treme Hypalon© glue – 0,5 kg

36.00

Two-component adhesive, available in tins of 0,5 kg or 1 kg.

Colour: black.

Suitable for glueing any Hypalon© and Neoprene based compound.

 

  • neoprene rubber layers
  • rubber handles / helms
  • latex terminals
  • valves
  • pockets / reinforcement patch

It can be used with the activator from 5% to 10%. On high and dry environmental temperatures we suggest to keep the lowest %.
For watertight applications, it is suggested the application of two coats of glue.
Ventilate the area during and after use.

How to Use

Surfaces must be polished before applying the glue and, if necessary, cleaned with a solvent to completely eliminate any and all plasticisers.

Mix half of the Big D® hardner bottle into the can and stir for 1 minute with a stick.

Apply with a short-haired brush an even and thin layer to both glue surfaces, leaving the solvent to fully dry. This process may take from 30 to 45 minutes, based on the environmental temperature.

Apply the adhesive / cross-linking mixture again and after about 20 minutes, warm up the surfaces with an hairdryer and pair the parts together while pressing down evenly.

To improve the end result and prevent air bubbles, use a roller before pressing. The dried product is odourless, flexible and resistant to ageing.

The vessel is ready for the water in 48 hours.

 

IMPORTANT: for using this glue you need to purchase the hardner too

Click here: Big D® glue hardner

 

Documents

Technical and Safety Data sheet – 07/01/2022

product photo

X-treme Hypalon© glue – 1 kg

45.00

Two-component adhesive, available in tins of 0,5 kg or 1 kg.

Colour: black.

Suitable for glueing any Hypalon© and Neoprene based compound.

 

  • neoprene rubber layers
  • rubber handles / helms
  • latex terminals
  • valves
  • pockets / reinforcement patch

It can be used with the activator from 5% to 10%. On high and dry environmental temperatures we suggest to keep the lowest %.
For watertight applications, it is suggested the application of two coats of glue.
Ventilate the area during and after use.

How to Use

Surfaces must be polished before applying the glue and, if necessary, cleaned with a solvent to completely eliminate any and all plasticisers.

Mix a full bottle of the Big D® hardner into the can and stir for 1 minute with a stick.

Apply with a short-haired brush an even and thin layer to both glue surfaces, leaving the solvent to fully dry. This process may take from 30 to 45 minutes, based on the environmental temperature.

Apply the adhesive / cross-linking mixture again and after about 20 minutes, warm up the surfaces with an hairdryer and pair the parts together while pressing down evenly.

To improve the end result and prevent air bubbles, use a roller before pressing. The dried product is odourless, flexible and resistant to ageing.

The vessel is ready for the water in 48 hours.

 

IMPORTANT: for using this glue you need to purchase the hardner too

Click here: Big D® glue hardner

 

Documents

Technical and Safety Data sheet – 07/01/2022

product photo

Glue hardner – 60 ml

13.00

The Big D® hardner is a part of the 2-component contact adhesive with a polychloroprenic gum and resin solution base, featuring a medium open time and high heat resistance.

Activator / accelerator / catalyst in bottle of 60 ml.

Purple color.

This product is what is needed to start gluing reaction with all Big D® glues.

Used from 5% to 10%, is provided a pasting cross-linking, with increase of the endurance and greater resistance to the action of reactivation generated by exposure to heat sources.

Ventilate the area during and after use.

DOCUMENTS

Technical sheet

Safety sheet

This glue is a very delicate Hypalon© glue. It has been developed as liquid neoprene, it is the most durable and resistant glue we could ever work out and grants a whole body with the surfaces which are gonna stick to each other.

IMPORTANT: this glue stains the fabric and is close to impossible to be removed once applied.

Works on Hypalon© rhibs, neoprene accessories, rubber supports, diving suits.